When you scan a chemical label, the two kinds of hazards to check for are physical hazards and health hazards. Physical hazards cover fire, explosion, reactivity, and pressurized-gas risks; health hazards cover toxicity, corrosion to skin or eyes, organ damage, and cancer risk. Both are mandatory sections on a GHS-compliant label, and both must inform how you store, handle, and protect yourself around the product.
Federal and international rules shape what appears on that label. In the United States, the Occupational Safety and Health Administration's Hazard Communication Standard, updated in 2012 and aligned again in 2024, requires chemical manufacturers to classify hazards and print six standardized label elements. Globally, the United Nations' Globally Harmonized System (GHS) sets the same two-hazard split across member countries. Knowing which hazard sits where on the label is the difference between reading a warning and actually being safe.
The Physical Hazard Class Covers Fire, Pressure, and Reactivity
Physical hazards describe what the chemical does to its surroundings. OSHA splits these into classes such as flammable liquids, flammable solids, gases under pressure, explosives, self-reactive substances, and oxidizers. A can of acetone with the flame pictogram and "H225: Highly flammable liquid and vapor" is signaling that its vapor can ignite at room temperature.
The severity categories matter. Flammable liquids run from Category 1 (flash point below 23 °C, boiling point at or below 35 °C, like diethyl ether) to Category 4 (flash point between 60 and 93 °C). A Category 1 label signals significantly higher fire risk than a Category 4 one, even though both carry a flame pictogram on some labels. Paying attention to the category number, not just the picture, changes how you store the product.
Gases under pressure are a distinct physical hazard, split into compressed, liquefied, dissolved, and refrigerated liquefied gas. A laboratory nitrogen cylinder falls in this group. The hazard isn't toxicity—nitrogen is inert—but a ruptured cylinder can become a projectile, and a leaking cylinder in a small room displaces oxygen. In 2019, a university lab in India reported a cylinder valve failure that injured two workers; the cause was traced to a missing valve cap during transport, a control the label's pressure pictogram warns about.
Reactivity belongs in this bucket too. Self-reactive substances and organic peroxides can decompose explosively if heated or contaminated. Hydrogen peroxide at concentrations above 8 percent is labeled as an oxidizer and, above 70 percent, as a Category 1 oxidizer with explosion risk. Mixing it with organic material in a drain can produce enough heat and gas to rupture plumbing.
The Health Hazard Class Covers Toxicity, Corrosion, and Disease
Health hazards describe what the chemical does to the body. OSHA's categories include acute toxicity, skin corrosion and irritation, serious eye damage, respiratory or skin sensitization, germ cell mutagenicity, carcinogenicity, reproductive toxicity, and specific target organ toxicity (STOT). A pesticide with the skull-and-crossbones pictogram plus "H300: Fatal if swallowed" is communicating an acute toxicity hazard in Category 1 or 2.
Corrosion hits fast. A bottle of 98 percent sulfuric acid carries "H314: Causes severe skin burns and eye damage." Even brief skin contact can cause full-thickness burns within seconds. The same class covers substances that damage metal, which is why corrosion labels sit under physical too when the chemical attacks steel—something many readers miss because they look for a single symbol.
Chronic health hazards often appear without a dramatic pictogram. The health hazard symbol—a human silhouette with a starburst on the chest—marks carcinogens, mutagens, reproductive toxins, respiratory sensitizers, and STOT substances. A can of spray paint may carry this symbol because of toluene's STOT and reproductive effects, not because the paint is acutely toxic. Reading the hazard statement ("H373: May cause damage to organs through prolonged or repeated exposure") tells you the risk is cumulative, not immediate.
Sensitization deserves its own attention. Isocyanates in two-part polyurethane foam carry "H317: May cause an allergic skin reaction." Once sensitized, a worker can react at exposure levels far below the original trigger. NIOSH reported that isocyanate asthma accounts for a meaningful share of occupational asthma cases in the auto body industry; the label's sensitizer warning is the first place to catch it.
The Signal Word Tells You How Seriously to Take Both Classes
Signal words come in two levels: Danger and Warning. Danger signals the more severe categories in either hazard class; Warning signals the less severe ones. If a product carries "Danger" once, it applies to the entire label. Reading which hazard the Danger belongs to changes your response—Danger for flammability is about fire, Danger for acute toxicity is about absorption or ingestion.
The placement of the signal word matters. Under OSHA's 29 CFR 1910.1200 Appendix C, the signal word, pictograms, and hazard statements are grouped by hazard class. A label can carry "Danger" for one hazard and "Warning" for another, but manufacturers typically print the highest-level signal word once at the top. The signal word applies to all hazards listed below it, which is why you read every hazard statement, not just the top line.
A common failure: assuming "Warning" means low risk overall. A product with "Warning" for skin irritation but "Danger" for eye damage in small print can cause permanent eye injury. The signal word hierarchy isn't a risk score; it's a labeling convention set by GHS. Treat every hazard statement independently.
If the signal word is missing entirely on a label, that's a red flag under OSHA rules. Industrial chemicals must carry one if a hazard exists. Consumer products under the Consumer Product Safety Commission's labeling rules follow different formats but still use "Danger," "Warning," or "Caution"—Caution being the lowest level, a word GHS doesn't use. On a household cleaner, "Caution" typically means lower acute hazard; on an industrial label, a missing signal word is a compliance failure.
Pictograms Are the Fastest Visual Check for Each Hazard Class
There are nine GHS pictograms, and they map roughly to the two classes. Five are primarily physical: flame, flame over circle (oxidizer), exploding bomb, gas cylinder, and corrosion (which spans both). Four are primarily health: skull and crossbones (acute toxicity), health hazard (chronic), exclamation mark (irritant, less severe), and environment (aquatic toxicity).
| Pictogram | Hazard Class | Example Product | Typical Signal Word |
|---|---|---|---|
| Flame | Flammable liquid/solid/gas | Acetone, spray adhesive | Danger |
| Flame over circle | Oxidizer | Hydrogen peroxide 30% | Danger |
| Exploding bomb | Explosive, self-reactive | Organic peroxide | Danger |
| Gas cylinder | Gas under pressure | Propane, nitrogen | Warning |
| Corrosion | Skin corrosion, eye damage | Sulfuric acid, lye | Danger |
| Skull and crossbones | Acute toxicity (Cat. 1–3) | Pesticide concentrate | Danger |
| Health hazard | Carcinogen, STOT, respiratory sensitizer | Toluene-based paint | Warning or Danger |
| Exclamation mark | Irritant, skin sensitizer, narcotic effects | Hand sanitizer | Warning |
| Environment | Aquatic toxicity | Many solvents | Usually none on GHS label |
The table is a shortcut, not a substitute. A pictogram tells you the class but not the category. The flame symbol spans Category 1 through 4 flammable liquids—four very different fire risks. The skull and crossbones spans acute toxicity Categories 1, 2, and 3, with lethal-dose thresholds that differ by routes of exposure.
You'll notice the environment pictogram isn't required in the U.S. under OSHA's hazard communication rule. It is required under GHS in the EU and other jurisdictions. If you're comparing labels across countries, the environment symbol's presence or absence tells you which regulatory regime printed the label.
Combining the Two Classes Gives You the Actual Risk Profile
A single label often carries hazards from both classes, and the combination matters more than either alone. A bottle of methanol is a flammable liquid (physical, Category 2) and an acute toxicant by ingestion, inhalation, and skin absorption (health, Category 3). That means it burns and it poisons you—and the fire hazard can distract from the absorption risk.
Take the case of a parts-washing solvent labeled "Danger" with both the flame and health hazard symbols. The fire risk is visible; the target-organ toxicity is not. Exposure over weeks through skin contact can cause liver damage even when ventilation is adequate for fire safety. Reading only the flame symbol leaves you unprotected against the hazard actually causing harm.
The pictogram count on a label tells you how many hazard classes apply. A label with five pictograms carries a more complex profile than one with two. That's a quick screen, not a risk ranking. A label with one pictogram—say, gas cylinder—can still kill you if the cylinder ruptures. But a label with five tells you to read every statement.
If a label lists both physical and health hazards, handle it for the more immediate risk first, then cover the chronic one. Immediate risk means fire, explosion, or acute poisoning; chronic risk means cancer, sensitization, or organ damage over time. Fire safety and PPE selection must address both at once—gloves for absorption, bonding and grounding for static ignition, ventilation for inhalation.
Read the Precautionary Statements as the Response Plan
Hazard statements describe the danger; precautionary statements describe what to do about it. Under GHS, precautionary statements are split into prevention, response, storage, and disposal (P-codes). "P210: Keep away from heat, sparks, open flames, hot surfaces" is prevention; "P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes, remove contact lenses, continue rinsing" is response.
The response statements are the ones to read under pressure. If a splash happens, you won't have time to look up a safety data sheet. The label's first-aid statement tells you the specific action for that product—some chemicals require flushing for 15 minutes, others for 20, and some (like hydrofluoric acid) require immediate calcium gluconate application and emergency medical care.
Storage codes differ from prevention codes in ways that matter. A product labeled "P403: Store in a well-ventilated place" may also carry "P235: Keep cool." A flammable liquid stored in a closed cabinet in a hot garage can build pressure and ignite. The label's storage section isn't decorative—it's the design specification for the container you put it in.
The GHS precautionary statement library is large, but labels typically carry 4–8 statements. Manufacturers choose the ones required by the hazard class and route of exposure. That means two products with the same hazard class and category usually carry the same statement set, so once you've learned one, you can read the pattern on next product.
GHS and OSHA Labels Place the Two Hazards in Fixed Positions
The label's layout is standardized, and knowing the layout speeds up the read. Under OSHA's 2012 and 2024 updates and the UN GHS model, a label carries six elements: product identifier, manufacturer contact details, signal word, pictograms, hazard statements, and precautionary statements. Health and physical hazard statements are grouped together in the hazard statement block—they aren't filed under separate headings that say "Physical" and "Health."
A compliant label from a major supplier like Fisher Scientific or Grainger usually prints the pictograms in a row, signal word top left, hazard statements in a block below. The "Danger" on a label with a flame, a skull and crossbones, and a corrosion symbol applies to all three—it's not assigned to only one.
The 2024 OSHA update to 29 CFR 1910.1200 changed some classification rules—particularly for aerosols and desensitized explosives—but retained the six-element structure and the two-hazard family split. If you're working from a label printed before 2012, or from a supplier that hasn't updated, the layout may follow the older OSHA format: no standardized pictograms, hazard information in prose. Those are still legal for certain older stock but are being phased out.
Small containers—under about 100 mL in many workplaces—may carry a reduced label. The rule allows the product identifier and pictograms plus a simplified hazard statement on very small containers, with full hazard information in the safety data sheet. If you pick up a small vial with only one symbol and a one-line warning, check the SDS for the full profile before assuming it's a single-hazard product.
The Safety Data Sheet Expands Both Hazards Beyond the Label
The label carries a summary; the safety data sheet carries the detail. The SDS is organized into 16 sections under GHS, and the two hazard classes live in distinct sections. Section 2 (Hazards Identification) lists every physical and health hazard with the classification code, and it's the fastest place to confirm what's on the label. Section 3 gives composition; Section 4 gives first aid; Section 5 firefighting; Section 6 spill response; Section 7 handling and storage; Section 8 exposure controls; Section 9 physical properties.
For physical hazards, Section 9 matters. Flash point, autoignition temperature, upper and lower explosive limits, vapor pressure—these are the numbers the label's flame pictogram summarizes. An acetone SDS reports flash point −20 °C and explosive limits 2.5 to 13 percent by volume in air. Those numbers determine whether a room's ventilation is adequate and whether a spark source is a real ignition risk.
For health hazards, Sections 8 and 11 matter. Section 8 gives occupational exposure limits (OSHA PELs, NIOSH RELs, ACGIH TLVs). Section 11 gives toxicological information including LD50 and LC50 values, target organ data, and carcinogenicity listings. The label's "H350: May cause cancer" ties to Section 11's specific listing—IARC, NTP, or OSHA's own carcinogen list.
A frequent failure is treating the label and SDS as the same source. The label omits the exposure limits, the toxicological data, and the incompatibilities in Sections 10. If you're deciding whether to buy a respirator or engineering control, the label won't tell you. The SDS does, and OSHA requires the SDS to accompany every hazardous chemical shipment in the workplace.
Storage, PPE, and Disposal Decisions Hang on the Two-Class Check
PPE selection depends on which hazard class dominates. For a physical hazard like flammability, gloves and eye protection prevent spills but the real control is ignition source elimination and bonding/grounding. For a health hazard like skin absorption, glove choice is the primary control—and the specific glove material matters, since nitrile fails against some solvents that butyl rubber resists.
Storage decisions split along the same lines. Flammables belong in approved flammable-storage cabinets sized to the quantity the local fire code allows—NFPA 30 is the common reference in the U.S., and the International Fire Code limits container sizes by occupancy. Health hazards with chronic effects may be stored in a ventilated cabinet with secondary containment even when flammability isn't a concern.
Disposal follows the hazard label. A waste stream carrying the flame symbol is regulated as ignitable hazardous waste under the Resource Conservation and Recovery Act (RCRA), which sets the flash-point threshold at 60 °C. A waste stream carrying the acute toxicity symbol may fall under the toxicity characteristic, which has different testing and manifesting rules under 40 CFR Part 261.
The two hazards sometimes conflict. A flammable solvent that's also a suspected carcinogen needs both fire-safe storage and vapor containment—flame arresters and closed containers, plus ventilation that captures vapor at the breathing zone. Reading only one hazard leads to a storage decision that addresses the fire but leaves the chronic exposure uncontrolled.
FAQ
Does "Danger" on a label cover both physical and health hazards?
Yes—the signal word applies to the entire label's hazard list, not just one class. A product labeled "Danger" for flammability and "Danger" for acute toxicity prints one signal word at the top because GHS uses the highest-level word once per label. Read the hazard statements to see which class each Danger belongs to, since "Danger" for fire and "Danger" for toxicity require different responses.
Can a chemical have a physical hazard but no health hazard?
Yes, and nitrogen gas is a common example. It carries the gas-cylinder pictogram and a "Warning" or "Danger" signal word for pressure, but no health hazard classification because it's inert and nontoxic. The risk is physical—asphyxiation from oxygen displacement or projectile injury from a ruptured cylinder—not toxicological, so don't assume "no health hazard" means safe.
What if the label has the health hazard pictogram but no acute toxicity symbol?
That's normal for chronic-only hazards. The health hazard silhouette marks carcinogens, mutagens, reproductive toxins, and STOT substances—categories that cause harm over time, not immediately. A can of paint with toluene may carry the health hazard symbol and a "H373" statement without the skull and crossbones, meaning acute poisoning isn't the primary concern but long-term organ damage is.
Is a safety data sheet required alongside every chemical label?
Yes, for workplace chemicals covered by OSHA's Hazard Communication Standard. The SDS carries the same two-hazard class information in Section 2, plus exposure limits, incompatibilities, and toxicological data the label omits. Consumer products sold to households are generally exempt from the workplace SDS rule, though many manufacturers still publish one on request.
Do I need different PPE for physical versus health hazards?
Often, yes. Physical hazards drive ignition control and pressure-relief equipment, while health hazards drive glove selection and respiratory protection. A solvent with both hazards may require nitrile gloves that resist the specific chemical plus bonding and grounding for static electricity—gloves for the health route, grounding for the physical one, both at the same time.
Are pictograms enough, or do I need to read every hazard statement?
Pictograms tell you the class; hazard statements give the category and route of exposure. The flame symbol appears on both a mildly flammable cleaner (Category 4) and a near-room-temperature-igniting solvent (Category 1), yet the required controls differ dramatically. Read the H-code next to each pictogram to know how severe the hazard actually is.
What should I do if a label is missing the signal word?
Treat it as a compliance failure and check the shipment's SDS before using the product. Under OSHA's 29 CFR 1910.1200, a hazardous chemical needs a signal word if any hazard exists; its absence usually means the label is outdated (pre-2012) or noncompliant. Don't rely on the missing word as evidence of low hazard—many older labels carried hazard info in prose only.
The information in this article is general educational material about label-reading conventions and does not constitute workplace safety guidance for any specific chemical or site. Chemical handling decisions depend on the product, quantity, conditions, and local regulations—consult your employer's safety officer, a qualified industrial hygienist, or your local occupational safety authority for advice specific to your situation. For immediate exposure or poisoning, contact your local poison control center or emergency services.