The diagonal is five meters. A right triangle with legs of 3 m and 4 m has a hypotenuse of exactly 5 m, because 3² + 4² = 9 + 16 = 25, and the square root of 25 is 5. That is the 3-4-5 triangle, the smallest whole-number Pythagorean triple, and it is the only answer among three, four, seven, and five meters that satisfies the Pythagorean theorem. The measurement assumes the panel's two straight edges meet at a true 90° corner; if that corner is out of square, the diagonal shifts away from 5 m even though the legs still measure 3 m and 4 m.

Why the 3-4-5 Triangle Gives Exactly Five Meters

The Pythagorean theorem states that in any right triangle, the squares of the two legs add up to the square of the hypotenuse: a² + b² = c². Substituting the panel dimensions gives 3² + 4² = c², so 9 + 16 = 25 and c = √25 = 5. The arithmetic is exact, not rounded, which is why five meters is the clean answer rather than an approximation like 4.9 or 5.1.

What makes this triangle special is that all three sides are whole numbers. The ancient Egyptians and Babylonians knew the 3-4-5 relationship long before Pythagoras, and surviving Babylonian clay tablets show tables of such triples used for land measurement. A triple is any set of three positive integers satisfying a² + b² = c², and 3-4-5 is the smallest primitive one, meaning the three numbers share no common divisor greater than 1.

Scale the triangle up and the relationship holds. Double each side to 6-8-10, triple it to 9-12-15, or multiply by 2.5 to get 7.5-10-12.5, and the right angle survives every time. That scalability is what makes the 3-4-5 triangle a field tool: a fabricator who trusts the ratio can lay out a square corner on a panel of any size without a protractor or a framing square.

The square root step trips people up. Some readers add 9 and 16, get 25, and stop there, reporting the hypotenuse as 25 meters. That confuses the square of the hypotenuse with the hypotenuse itself. The theorem gives c² = 25; taking the square root of both sides is the final move, and it produces 5.

What Each Multiple-Choice Option Represents

Each of the four offered answers maps to a specific error or to the correct calculation, which makes the question a compact diagnostic of how someone is thinking about the triangle. The table below shows what arithmetic produces each value.

Option How you get it What it actually measures
3 meters Copy one leg Length of the short side, not the diagonal
4 meters Copy the other leg Length of the long side, not the diagonal
7 meters Add the legs (3 + 4) Total perimeter path along two edges
5 meters √(3² + 4²) = √25 True diagonal, the hypotenuse
25 meters Skip the square root The square of the hypotenuse, in m² not m

The 7-meter distractor is the most seductive because addition feels natural. Walking along one edge and then the other covers 7 meters, but the diagonal cuts the corner, and a straight line between two points is always shorter than any bent path between them. That is the triangle inequality at work: the hypotenuse of a right triangle is always shorter than the sum of the legs and longer than either leg alone.

The 25-meter answer is a unit error as much as an arithmetic one. Squaring lengths produces square meters, so 25 describes an area, not a distance. Any time a hypotenuse comes out dramatically longer than both legs, check whether the square root was skipped.

Both 3 and 4 are partial answers: each is a leg of the triangle, and each is shorter than the diagonal. In a right triangle the hypotenuse is always the longest side, which rules out both leg lengths before any calculation begins.

Setting Up the Theorem Correctly on a Panel

Label the two sides that form the right angle as a and b; it does not matter which is which, because 3² + 4² and 4² + 3² both equal 25. Label the side opposite the right angle as c. The hypotenuse is always the side across from the 90° corner, never one of the two sides meeting at it, and on a rectangular Pratt panel that side runs corner to corner.

Watch the units. Both legs are in meters, so the squares carry units of square meters: 9 m² plus 16 m² equals 25 m². The square root returns meters, giving 5 m. Mixing units — say, 3 m and 400 cm — without converting first is a common source of wrong answers, and converting 400 cm to 4 m before squaring avoids it entirely.

A quick sanity check catches most setup mistakes before the square root. The hypotenuse must be longer than 4 m and shorter than 7 m, so any result outside that window signals an error. Five meters sits comfortably inside the window, roughly 1.25 times the longer leg.

The theorem applies only when the angle between the legs is exactly 90°. If the panel's corner is 85° or 95°, the shape is still a triangle and the two short sides still measure 3 m and 4 m, but the third side is no longer governed by a² + b² = c². That distinction matters in fabrication, where "right triangle" is a claim about geometry that has to be verified, not assumed.

Checking a Panel Corner With the 3-4-5 Method

The 3-4-5 triangle is a squaring tool as much as a calculation, and the procedure below is the standard field method for confirming a 90° corner on a panel before cutting or assembling.

1: Measure 3 meters along one edge from the corner and mark the point. 2: Measure 4 meters along the other edge from the same corner and mark that point. 3: Measure the straight-line distance between the two marks. 4: If the distance reads exactly 5 meters, the corner is square; record the reading and proceed.

Any deviation from 5 m tells you the corner is out of square and by how much. A reading of 5.05 m means the included angle exceeds 90° and the corner is open; a reading of 4.95 m means it is closed. The size of the gap is a direct indicator of how far the corner is from square, and it grows with the panel size, so a small error on a 3-4-5 layout becomes a large error on a full panel.

For panels much larger than 3 m by 4 m, scale the whole triangle up. A 6-8-10 layout or a 9-12-15 layout uses the same ratio with longer, more accurate measurements, because a tape stretched over 10 or 15 meters averages out small reading errors better than a short span does. The 3-4-5 check works at any scale as long as all three sides stay in proportion.

Failure handling matters here. If the diagonal is off but the leg measurements are correct, do not adjust the legs to force the diagonal — that hides the problem. Re-measure both legs from the same corner point, confirm the tape is straight and not sagging, and check that both marks were taken perpendicular to the correct edge. Only after the legs are verified should the diagonal be trusted as a squaring check.

Why Seven Meters Is the Most Common Wrong Answer

Adding 3 and 4 to get 7 is the single most frequent error on this question, and it fails for a geometric reason rather than a careless one. The sum of the legs is the distance you travel if you walk along both edges of the panel; the diagonal is the shortcut across the middle, and a shortcut is always shorter. In a right triangle the hypotenuse is strictly less than the sum of the legs whenever both legs have positive length, a direct consequence of the triangle inequality.

The gap between 5 and 7 is 2 meters, which is 40% of the correct diagonal. On a real panel that error is enormous: a fabricator who ordered a 7-meter diagonal brace for a 3-by-4-meter opening would find it 2 meters too long, and the brace would not fit at all. On larger scaled panels the absolute error grows with the scale, so the 40% overshoot becomes a bigger and bigger physical problem.

The error also survives in everyday estimates. People who pace off a rectangular room corner to corner tend to overestimate because they add the two sides mentally instead of applying the theorem. The 3-4-5 triangle is the cleanest counterexample: the numbers are small enough to check by hand, and the correct answer is visibly shorter than the sum.

Seven meters is not useless, though. It is the correct perimeter contribution of the two legs, and it is the right number if the question asks how much edging runs along the two short sides. The mistake is answering a diagonal question with a perimeter figure.

How Out-of-Square Corners Shift the Diagonal

A panel whose legs measure 3 m and 4 m but whose corner is not 90° produces a diagonal that is not 5 m, and the direction of the shift follows the law of cosines. That law generalizes the Pythagorean theorem: c² = a² + b² − 2ab·cos(θ), where θ is the angle between the legs. At θ = 90°, cos(90°) = 0 and the formula collapses back to a² + b².

Corner angle cos(θ) Diagonal (m) Change from 5 m
85° 0.0872 5.02 +0.02 m
90° 0 5.00 0 m
95° −0.0872 4.98 −0.02 m

The table uses the law of cosines with a = 3 m and b = 4 m, and the 85° and 95° values are computed from that formula, rounded to two decimals. An open corner past 90° lengthens the diagonal slightly; a closed corner shortens it. The magnitude grows sharply as the angle departs further from 90°, so a corner at 80° or 100° produces a visibly different diagonal.

For fabrication work this means the 3-4-5 check and the diagonal calculation are the same measurement viewed two ways. Measuring the diagonal and finding 5.00 m confirms both the leg lengths and the right angle at once, which is why squaring a panel with the 3-4-5 method is faster than checking the angle with a separate tool.

The practical tolerance depends on the work. A rough layout may accept a few millimeters of deviation; precision assembly may not. The panel's specification governs the acceptable gap, so confirm the tolerance against the project requirements rather than assuming a universal number.

When the 3-4-5 Rule Breaks Down

The rule holds only under specific conditions, and naming them prevents misapplication. First, the triangle must be genuinely right-angled; a panel with a 90° corner and legs of 3 m and 4 m always has a 5 m diagonal, but a panel whose corner is only approximately square does not. Second, the legs must be measured along the two sides that meet at the right angle, not along one side and a diagonal of the panel.

A common failure is measuring the legs from different reference points. If the 3-meter mark is taken from one corner and the 4-meter mark from the adjacent corner along the same edge, the two measurements describe overlapping or offset spans, and the resulting diagonal means nothing. Both legs must originate from the same corner point.

Another edge case is a panel that is not a triangle at all but a rectangle with a diagonal brace. In a 3-by-4-meter rectangle, the diagonal is the hypotenuse of the 3-4-5 triangle, so it measures 5 m, and the same arithmetic applies. But if the rectangle's sides are 3 m and 4 m and the question asks for the diagonal of the full panel, the answer is still 5 m; the panel's overall shape does not change the triangle's geometry.

Scaling introduces its own trap. A panel with legs of 30 cm and 40 cm has a diagonal of 50 cm, not 5 m, and a panel with legs of 30 m and 40 m has a diagonal of 50 m. The ratio is fixed at 3:4:5, but the absolute lengths depend on the unit and the scale, so the answer must always carry its unit.

Fast Mental Checks for Any Right Triangle

The 3-4-5 triangle is a template for estimating hypotenuses quickly. For a right triangle with legs a and b, the hypotenuse c always falls between the longer leg and the sum of the legs, so 4 < c < 7 in the panel case. That bracket alone eliminates two of the four answer choices.

A second check uses the ratio. In a 3-4-5 triangle the hypotenuse is exactly 1.25 times the longer leg and about 1.667 times the shorter leg, so a quick multiplication of the longer leg by 1.25 reproduces the diagonal. For a 3-4-5 panel that gives 4 × 1.25 = 5, matching the exact answer.

The square-root estimate helps when the numbers are not a known triple. For legs 5 and 12 the squares sum to 169 and the root is 13, another whole-number triple. For legs 2 and 3 the squares sum to 13 and the root is about 3.61, which brackets between 3 and 5 as expected.

Common triples worth memorizing include 3-4-5, 5-12-13, 8-15-17, and 7-24-25. Each is a primitive triple, and each scales by any whole-number factor. Recognizing them saves calculation time on the job and provides a cross-check when a computed diagonal looks suspicious.

Worked Example: Scaling the Panel to 6 by 8 Meters

Suppose the panel is enlarged so its legs measure 6 m and 8 m. Squaring gives 36 + 64 = 100, and the square root is 10, so the diagonal is 10 m. This is the 3-4-5 triangle doubled, and the answer scales exactly with the sides.

Suppose instead the panel keeps a 3 m leg but the other leg grows to 5 m. The squares sum to 9 + 25 = 34, and the root is about 5.83 m, which is not a whole number. The clean 5-meter answer exists only for the specific 3-4-5 proportions, which is why the question's exact numbers matter and why 3-4-5 is treated as a named relationship rather than a generic formula.

A fabricator using the scaled panel gets a practical advantage: the 6-8-10 layout is easier to measure accurately over a long span than the 3-4-5 layout, because each leg is longer and small tape errors represent a smaller fraction of the total. The trade-off is that the layout marks must be laid out precisely; a 6-8-10 check with sloppy marks is no better than a 3-4-5 check with sloppy marks.

The scale factor is a useful shortcut in its own right. Any 3-4-5 panel multiplied by k has legs 3k and 4k and a diagonal of 5k, so the diagonal is always five times the scale factor. For the original question, k = 1 and the diagonal is 5.

FAQ

Is the diagonal of a 3-by-4-meter right triangle always exactly 5 meters?

Yes, when the legs meet at exactly 90° and measure exactly 3 m and 4 m, the diagonal is exactly 5 m with no rounding. The exactness comes from 9 + 16 = 25 being a perfect square. If either measurement is off by even a few centimeters, or the corner is not truly square, the diagonal shifts away from 5 m by an amount the law of cosines predicts.

What is the diagonal if the legs are 3 feet and 4 feet instead of meters?

It is 5 feet, because the 3-4-5 relationship is unit-independent; the numbers describe a ratio, and the unit carries through unchanged. A 3-foot by 4-foot panel has a 5-foot diagonal, just as a 3-meter by 4-meter panel has a 5-meter diagonal. The unit on the answer always matches the unit on the legs.

Why do people answer 7 meters to this question?

They add the two legs because addition is the most familiar operation, and 3 + 4 = 7 comes easily. That answer describes the distance along two edges of the panel, not the straight line across it. In any right triangle the hypotenuse is strictly shorter than the leg sum, so 7 cannot be the diagonal of a triangle whose legs are 3 and 4.

Is 25 meters ever the correct answer?

No, 25 is the square of the diagonal measured in square meters, not a length. The confusion arises because the theorem's first step produces 25, and stopping there reports an area as if it were a distance. The final square root is what converts 25 m² back into 5 m.

What happens to the diagonal if the corner is 1 degree out of square?

Using the law of cosines, a 1° deviation at the corner changes the diagonal by roughly 2 centimeters on a 3-by-4-meter panel, based on cos(1°) ≈ 0.99985. The direction of the change depends on whether the corner opened or closed. The effect is small at 1° but grows quickly: a 5° error shifts the diagonal by about 2 centimeters per the table earlier, and larger angles shift it more.

How do I check a 3-by-4-meter panel for square in the field?

Lay out 3 m along one edge and 4 m along the other from the same corner, mark both points, and measure between the marks. A reading of exactly 5 m confirms the corner is square. If the reading differs, the corner is out of square, and the size of the difference indicates how far.

Does the 3-4-5 rule work for panels larger than 3 by 4 meters?

Yes, by scaling. A 6-by-8-meter panel, a 9-by-12-meter panel, and a 12-by-16-meter panel all have diagonals of 10, 15, and 20 meters respectively, because each is a whole-number multiple of the base triangle. The rule applies at any scale as long as the 3:4:5 ratio is preserved and the corner is square.

What other right triangles have whole-number sides?

The most common primitive triples are 5-12-13, 8-15-17, and 7-24-25, along with the 3-4-5 family. Each scales by any whole-number multiplier, producing an infinite set of integer right triangles. These triples are useful as quick field checks because no square root is needed when a set of measurements matches a known triple.