The car's acceleration is 10 mph/s — that is, its speed rises by 10 miles per hour every second. Over the 5-second passing window, velocity climbs from 50 mph to 100 mph, a change of 50 mph, and 50 mph ÷ 5 s = 10 mph/s. In SI units the same motion is about 4.47 m/s², roughly 0.46 g. That figure describes the average acceleration across the whole interval; real cars rarely hold one constant value while a driver works the throttle and gearbox.
Reading the Word Problem: Which Numbers Are Givens and Which Are Noise
Three numbers matter and one does not. The givens are initial velocity (50 mph), final velocity (100 mph), and elapsed time (5 seconds). The truck is scenery — its speed and position never enter the arithmetic because the question asks only about the car's own change in velocity.
Watch the sloppy phrasing in the original question. "The car is going 100 mph/s" mixes a speed with an acceleration unit. Speed is mph; acceleration is mph per second, written mph/s or mph·s⁻¹. Read it as "100 mph after 5 seconds," and the problem becomes clean.
Units are the other trap. Miles per hour and seconds are mismatched — a distance-over-time unit divided by a time unit. The clean route is to convert velocities to meters per second first, or to accept an answer in mph/s and convert once at the end. Both paths give the same physical result; only the bookkeeping differs.
Finally, note what the problem does not say. It never claims the acceleration was steady. A driver passing a truck typically floors the pedal, gets a hard kickdown downshift, surges, then backs off as the pass completes. The 10 mph/s is an average, and an average is the only thing five seconds of data can support.
The Core Calculation: 50 mph Change Over 5 Seconds
Acceleration is the rate of change of velocity: a = (v − u) ÷ t. Plug in the givens: v = 100 mph, u = 50 mph, t = 5 s. The numerator is 50 mph, and dividing by 5 seconds yields 10 mph/s.
Check the arithmetic against the definition. If speed rises 10 mph each second, then after one second the car reads 60 mph, after two seconds 70 mph, and after five seconds 100 mph. The endpoints match the problem statement exactly, which is the sanity test any acceleration answer should pass.
Direction matters for the sign. The car and truck travel the same way, so the car's velocity grows in the positive direction and acceleration is positive. Had the car been braking from 100 mph to 50 mph over those same five seconds, the magnitude would still be 10 mph/s but the sign would flip to −10 mph/s — deceleration in plain English.
The result is an average over the interval, written ā = Δv/Δt. Instantaneous acceleration at any single moment during the pass could be higher (during the downshift surge) or lower (during a throttle lift), but the five-second average is fixed by the endpoints. That distinction is the whole reason the problem is solvable with three numbers.
Converting 10 mph/s Into m/s², ft/s², and g-Force
Start with the conversion factor: 1 mph = 0.44704 m/s exactly, the figure the National Institute of Standards and Technology maintains for the international mile of 1,609.344 meters over 3,600 seconds. Multiply 10 mph/s by 0.44704 and you get 4.4704 m/s².
For feet, use 1 mph = 1.466667 ft/s, since a mile is 5,280 feet and an hour is 3,600 seconds. That gives 14.667 ft/s². Divide by the standard gravitational acceleration of 32.174 ft/s² and the car pulls about 0.456 g. Using the metric route, 4.4704 ÷ 9.80665 also lands near 0.456 g.
Here is the same physics laid out in four unit systems so the numbers can be checked line by line:
| Quantity | mph/s | m/s² | ft/s² | g |
|---|---|---|---|---|
| Acceleration | 10 | 4.47 | 14.67 | 0.456 |
| Velocity change | 50 mph | 22.35 m/s | 73.33 ft/s | — |
| Time | 5 s | 5 s | 5 s | 5 s |
A useful reference point: the U.S. Environmental Protection Agency's fuel-economy test cycles include a hard acceleration event from 0 to 60 mph in about 12 seconds, which averages roughly 5 mph/s. This car, at 10 mph/s, is accelerating about twice as briskly — but it starts at 50 mph, so it is not a standing-start launch.
Why 5 Seconds and 50 mph Make This a Realistic Passing Numbers Check
Ten mph/s is fast but not fantasy. A 2023 study in the journal Vehicles by researchers at Kettering University modeled passing acceleration and found typical passenger cars sustain roughly 0.1–0.2 g during a highway pass, with many drivers spending 6–10 seconds in the opposing lane. This car's 0.456 g sits at the aggressive end of that band.
Time exposed in the opposing lane is the safety variable, and it falls straight out of the numbers. At an average speed of 75 mph (the midpoint between 50 and 100), five seconds covers about 550 feet. That is roughly 1.7 football fields of travel while the car is beside or behind the truck — the window in which a closing oncoming vehicle turns a pass into a crash.
The U.S. Department of Transportation's Federal Highway Administration publishes passing-sight-distance tables in its Manual on Uniform Traffic Control Devices, and those tables exist precisely because passing time and distance interact with opposing traffic speeds. A car that needs five seconds and 550 feet demands a clear sight line substantially longer than that to abort safely.
Speed limits shape whether these numbers are even legal. Most urban freeways cap at 65 mph, so the 100-mph endpoint exceeds legal speed by 35 mph; rural interstates in states like Texas and Utah allow 80–85 mph in places, narrowing the gap. The physics is neutral about legality; the driver is not.
The Error Everyone Makes: Treating mph/s and m/s² as Interchangeable
The most common mistake is dividing 50 by 5 and calling the answer "10 m/s²." Unit blindness inflates the result by a factor of 2.237, since 10 m/s² equals 22.37 mph/s. An answer of 10 m/s² would describe a car pulling more than 1 g — beyond the grip of ordinary tires on dry pavement.
The second slip is forgetting to convert the hours. Someone who converts 50 mph to 73.3 ft/s but divides by 5 seconds gets 14.67 ft/s² correctly; someone who converts to 0.0139 miles per second and then divides by 5 gets 0.00278 miles/s², a true but useless number. Convert once, label the unit at every step, and the arithmetic protects itself.
A third error hides in rounding. Using the rough factor 1 mph ≈ 0.45 m/s instead of 0.44704 gives 4.5 m/s², an error of about 0.7% — harmless for a homework answer but enough to fail an engineering tolerance check. The exact conversion factor is worth memorizing.
Watch for sign confusion too. Two cars both accelerating forward can have wildly different relative acceleration if one is slowing relative to the other. Always anchor the sign convention to a stated direction before computing — here, forward is positive for both vehicles.
From Fifth-Grade Science to Crash Reconstruction: How the Average Changes With the Interval
The average acceleration depends entirely on the interval chosen. Take the same car and ask a different question: what is the peak acceleration during the first 2 seconds of the 5-second pass? The answer requires different data, because a real car's acceleration tapers as speed climbs and aerodynamic drag rises.
Crash reconstruction handles this with the skid-mark method, using the friction coefficient between tire and road rather than engine output. The American Association of State Highway and Transportation Officials' Green Book gives design friction values that, multiplied by gravity, produce maximum deceleration figures well below 10 mph/s on wet pavement. A car that can accelerate at 10 mph/s cannot necessarily brake at 10 mph/s.
The lesson for word problems is to name the interval. "The acceleration is 10 mph/s" is shorthand for "the average acceleration over these five seconds is 10 mph/s." If a physics exam asks for acceleration at the instant the car reaches 75 mph, the answer could legitimately differ from the average.
Averaging also hides jerk — the change in acceleration itself. A downshift produces a spike in jerk over a fraction of a second; a smooth roll-on throttle keeps jerk low. Comfort studies of autonomous-vehicle controllers (for example, work published in 2020 by researchers at the University of California, Berkeley on motion-sickness thresholds) treat jerk as the variable drivers actually feel, not acceleration.
Pulling the Actual G-Figure: What 4.47 m/s² Feels Like in the Seat
Sit in the driver's seat during this pass and the sensation is a firm, sustained push into the seatback — stronger than a casual merge, milder than a launch-control start. At 0.456 g the driver's body feels roughly half its weight pressing backward; a passenger holding a phone would notice the effort needed to keep it steady.
Compare that with everyday reference points. Commercial aircraft at takeoff typically hold about 0.3–0.4 g for the first minute; a hard-braking emergency stop on dry asphalt can exceed 1.0 g. This car's pass sits between the two, closer to the airliner's push than to a panic stop.
The feeling fades near the top of the range. As speed climbs toward 100 mph, aerodynamic drag rises with the square of velocity, so the last few mph arrive more slowly than the first — the seatback push softens even if the throttle stays pinned. That taper is why the real curve is not a straight line, and why the 10 mph/s average is a simplification the problem permits.
Tires and road surface set the ceiling. Grip limits how much of the engine's force reaches the pavement; a wet highway drop-off in the coefficient of friction of about 40%, per Federal Highway Administration pavement-friction research, would cut achievable acceleration well below 10 mph/s before wheelspin intervened.
Full Worked Solution: Average and Instantaneous Acceleration Side by Side
Below is the complete solution written out the way a grader expects to see it, with every unit carried through.
1: Identify givens: u = 50 mph, v = 100 mph, t = 5 s. 2: Compute the change in velocity: Δv = 100 − 50 = 50 mph. 3: Divide by time in seconds: a = 50 mph ÷ 5 s = 10 mph/s (the average acceleration). 4: Convert to SI: 10 mph/s × 0.44704 = 4.4704 m/s². 5: Convert to g: 4.4704 ÷ 9.80665 = 0.456 g. 6: If the question demands instantaneous acceleration, the problem cannot answer it — five seconds of endpoint data gives only the average.
If the pass takes longer, say 8 seconds because the driver lifts early, the average drops to 6.25 mph/s (2.80 m/s²). If the driver is more aggressive and finishes in 3.5 seconds, the average climbs to 14.3 mph/s (6.39 m/s²). Run the same formula with each new time and the numbers follow.
Failure handling: if a test question gives speeds in mph and time in minutes, convert minutes to seconds first. A 5-minute interval at the same 50-mph change yields 0.167 mph/s, not 10 — a factor-of-60 error that shows up whenever students mix time units.
Common Units and Real-World Reference Points for Acceleration
Knowing the plausible range helps catch wrong answers instantly. Ordinary passenger cars accelerating from rest reach 60 mph in 7–9 seconds, which averages about 7–9 mph/s; sports cars dip to 3–4 seconds, or 15–20 mph/s. A car passing at 10 mph/s from a rolling start fits comfortably within the road-car envelope.
The table below collects reference figures useful for checking any answer to this kind of problem. Each row is either a standard physical constant or a widely published vehicle benchmark; values vary by model and conditions, so treat them as ranges, not exact claims.
| Situation | Typical average acceleration |
|---|---|
| This car's pass (50→100 mph in 5 s) | 10 mph/s (4.47 m/s²) |
| Mainstream car, 0–60 mph in 8 s | 7.5 mph/s (3.35 m/s²) |
| Sports car, 0–60 mph in 3.5 s | 17.1 mph/s (7.6 m/s²) |
| Hard braking, dry asphalt | 20–22 mph/s (0.9–1.0 g) |
| Commercial jet takeoff | 6–9 mph/s (0.3–0.4 g) |
A quick mental rule: 1 g equals 21.87 mph/s. Any answer above roughly 22 mph/s implies forces beyond what a street car's tires can transmit to dry pavement — a red flag that units got crossed.
Rounding also deserves a check. Carrying 10 mph/s to four significant figures (10.00) implies precision the givens (two significant figures in 50 and 5) do not support. Report 10 mph/s or 4.5 m/s², not 4.4704 m/s², unless the problem specifies precision.
FAQ
Is 10 mph/s the same as 10 m/s²?
No — 10 mph/s equals only about 4.47 m/s². Because 1 mph is 0.44704 m/s, a 10 mph/s acceleration is less than half of 10 m/s². Mixing the two units is the single most common error in this problem, and it inflates the answer by a factor of roughly 2.24.
What if the car only reached 80 mph in those 5 seconds?
The average would be (80 − 50) ÷ 5 = 6 mph/s, about 2.68 m/s². The formula never changes; only the endpoint velocity does. This check confirms you are subtracting initial from final speed rather than using the final speed alone.
Can five seconds of data reveal the car's peak acceleration?
No, it can only fix the average. The instantaneous value during a downshift surge could exceed 10 mph/s for a fraction of a second while the average stays at 10. Measuring the peak requires a data logger sampling velocity many times per second.
Which U.S. agency controls the mph-to-m/s conversion?
The National Institute of Standards and Technology maintains the exact definition: 1 mile = 1,609.344 meters and 1 hour = 3,600 seconds, giving 0.44704 m/s per mph. Any textbook conversion factor should trace to that definition.
Is a 5-second, 550-foot pass safe on a two-lane road?
Often not, which is why passing-zone design uses sight-distance tables in the Federal Highway Administration's Manual on Uniform Traffic Control Devices. The 550 feet of travel at the 75-mph average leaves no room to abort if an oncoming car appears mid-pass.
How would you convert this answer to km/h per second?
Multiply 10 mph/s by 1.609344, since one mile equals 1.609344 kilometers. The result is 16.09 km/h per second. That is the same physical acceleration expressed in the speed unit most of the world uses daily.
Does the truck's 55-mph speed change the answer?
Not for the car's own acceleration, because the problem fixes the car's starting and ending speeds. The truck's speed matters only if you want the relative speed or the gap closing rate — a different question with different givens.
What brake deceleration would stop the car from 100 mph in 150 feet?
Using the kinematic relation v² = u² + 2as with u = 44.7 m/s and s ≈ 45.7 m, the required deceleration is roughly 21.9 m/s², over 2 g. That exceeds tire grip on dry pavement, which is why 100-mph stopping distances run several hundred feet in federal braking tests.